Nano V3.0 - clone with ATTiny88 and Micro USB - compatible with Arduino
Add products by adding codes
Add a CSV file
Enter the product codes that you want to add to the cart in bulk (after a comma, with a space or from a new line).
Repeating the code many times will add this item as many times as it appears.
Miniature development board based on ATTiny88 microcontroller, operating at 16 MHz. Equipped with Micro USB connector and self-soldering connectors. Perfect for compact electronic projects.
Nano V3.0 - clone with ATTiny88 and Micro USB - compatible with Arduino
$4.19
Nano V3.0 - clone with ATTiny88 and Micro USB - compatible with Arduino
Universal mini-module compatible with the original Arduino, equipped with ATTINY88 microcontroller and Micro USB connector (version with pins for self-soldering). Can be used in many microprocessor projects. Circuit compatible with Arduino IDE project.
Faithfully reproduced clone is a certainty of performance and reliability.
Thanks to the convenient USB type-C connector, it is hassle-free to connect this module under a computer and program it. Thanks to its small size, it will work well in smaller projects.
The module uses the Atmega T88 microcontroller.
Nano has a voltage stabilizer so we can power the module from a voltage higher than 5V.
NOTE!!!
The Nano has a new bootloader uploaded, which works with ArduinoIDE version 1.8 upwards.
Product features
The Nano version, like the Pro, is based on the popular Uno module
It has an Atmega T88 microcontroller
The board contains an ATmega T88 processor chip with a
32kB Flash memory
1kB SRAM
1kB of EEPROM memory
It is clocked with a 16 MHz clock signal.
The board has pins - outputs/inputs
including 6 PWM channels e.g. for controlling servos / motors e.g SG-90
14 digital pins - can be used as input or output. Pins operate in TTL5V standard. The capacity of each reaches 40mA, and they have built-in pull-up resistors. Some of the pins have additional functions (UART, INT, PWM, SPI, LED).
8 analog inputs, each allowing measurement with 10-bit resolution. Some of the pins have additional functions (I²C, AREF, Reset).
The Nano module can be powered by
via Micro USB cable
with an unstabilized voltage of 7-12V applied to pin 30 or from a stabilized voltage source of 5V.
The system automatically selects the power source with the highest voltage.
CH340 chip that provides communication with the computer can only be powered by USB.
The chip has a system of communication with the computer through:
uART interface - derived on pins 0 (RX) and 1 (TX).
USB - CH340 chip
In addition, I²C (TWI) and SPI interfacing are supported
Works with voltages of 5 V.
Switch for manual reset
LEDs to control the operation of the system
Connectors arranged on the board allow the board to be plugged directly into the contact board.
This version has soldered connector pins
The microcontroller on the board has a bootloader pre-installed, which allows software to be uploaded without additional hardware.
In addition, it is possible to program the processor via ICSP.
Technical data
Supply voltage: 5V
Microcontroller: ATmega T88 - 16 MHz
Ports - I/O pins: 14
Number of analog inputs: 8
Number of PWM outputs: 6
Serial interfaces: UART, SPI, I2C
External interrupts
Protection against the flow of too much current
Module made on 0.8 mm thick laminate
Weight less than 5 g.
pin spacing 2.54mm (can be mounted in contact boards)
Dimensions: 45x19 mm
32kB flash memory
1kB EEPROM
1kB SRAM
2 8bit timers/counters
1 timer/counter 16bit
connector: Micro USB
Construction and connection notes
Power supply
If the supply voltage is higher than 5 V, it should be connected to the RAW pin, which is connected to the stabilizer.
VCC is connected directly to the pins of the microcontroller, connecting a voltage higher than 5 V can permanently damage the chip.
Inputs/outputs
Arduino Pro has 14 digital input/output (I/O) leads.
Each pin allows a maximum current draw of 40 mA, allowing direct connection of LEDs with resistors and control of other ICs.
In addition to standard I/O, some leads also have special functions.
Programming
Software development and uploading is enabled by a free environment provided by the manufacturer.
ProducerWide Top Industrial LimitedAddress:
DongYuan Road, Woshi, Qiaodong Street,Xiangqiao District ,Chaozhou No 32Postal Code: NO 41-47City: ChaozhouCountry: ChinyPhone number: +86-13715708628E-mail: wide@aliyun.com
Responsible entityABC-RC Firma LedaAddress:
Judy Tadeusza 9Postal Code: 34-122City: NidekCountry: PolskaPhone number: 333-003-080E-mail: pomoc@abc-rc.pl
Symbol
18793
Producer code
5904384743186
Status
New
Manufacturer
AF
Model
NANO V3.0 16MHz Micro USB - ATmega328P - CH340
Manufacturer code
17529
Rodzaj
inny
Do you need help? Do you have any questions?Ask a question and we'll respond promptly, publishing the most interesting questions and answers for others.
w tym wpisie zajmiemy się programowaniemAtTiny85czyli jednej z odnóg rodziny mikrokontrolerów Atmel-a. Cechą charakterystyczną dla tej rodziny jest ich minimalistyczność, a więc małe wymiary ukryte pod postacią najczęściej 8 pinowego układu w bardzo atrakcyjnej cenie.
can be used 
