Add products by adding codes
Add a CSV file
Enter the product codes that you want to add to the basket in bulk (after a comma, with a space or from a new line).
Repeating the code many times will add this item as many times as it appears.
NANO V3.0 16MHz USB - ATmega328PB - CH340 - Clone - solder pins - compatible with Arduino
Product code: 9588
- Universal mini-module compatible with the original Arduino, equipped with ATmega328PB microcontroller and USB connector (self-solder pin version). Can be used in many microprocessor projects.
NANO V3.0 16MHz USB - ATmega328PB - CH340 - Clone - Arduino compatible
Universal mini-module compatible with the original Arduino, equipped with ATmega328PB microcontroller and USB connector (self-solder pin version). Can be used in many microprocessor projects. Circuit compatible with Arduino design.
- Faithfully reproduced clone is a certainty of performance and reliability.
- NANO has a CH340 programmer for which you need an additional controller, which is below.
- Thanks to the convenient mini USB connector, it is effortless to connect this module to a computer and program it. Thanks to its small size, it will work well in smaller projects.
- The Arduino uses the Atmega328 microcontroller.
- Nano has a voltage stabilizer so we can power the module from a voltage higher than 5V.
NOTE!!!
The Nano has an old bootloader preloaded, which works with ArduinoIDE up to version 1.6. and this version of the software should be downloaded.
Product features
- The Nano version, like the Pro, is based on the popular Uno module
- It has an Atmega328PB microcontroller.
- On the board USB connector with CH340 chip
- The board contains an ATmega328 processor chip with 32kB of Flash memory, 1kB of SRAM, 1kB of EEPROM. It is clocked with a 16 MHz clock signal.
- The board has pins - outputs/inputs, including 14 digital pins and 8 analog inputs.
- The Arduino Nano can be powered via a mini-USB cable, with a 7-12V unstabilized voltage fed to pin 30 or from a stabilized 5V voltage source. The system automatically selects the power source with the highest voltage.
- The chip has a system for communicating with a computer via UART, USB, I²C (TWI) and SPI interfaces.
- Works with voltages of 5 V.
- Switch for manual reset, LEDs for monitoring system operation.
- Connectors arranged on the board allow the board to be plugged directly into the contact board.
- This version has soldered connector pins.
- For programming, use the Arduino IDE, free software that is extremely beginner-friendly.
- The microcontroller on the board has a bootloader pre-installed, which allows software to be uploaded without additional hardware.
- In addition, it is possible to program the processor via ICSP.
Technical data
- Supply voltage: 5V
- Microcontroller: ATmega328PB - 16 MHz
- Ports - I/O pins: 14
- Number of analog inputs: 8
- Number of PWM outputs: 6
- Serial interfaces: UART, SPI, I2C
- External interrupts
- Protection against the flow of too much current
- Module made on 0.8 mm thick laminate
- Weight less than 5 g.
- Pin spacing 2.54mm (can be mounted in contact boards)
- Dimensions: 45x19 mm
- 32kB flash memory, 1kB EEPROM, 1kB SRAM
- 2 timers/counters 8bit, 1 timer/counter 16bit
Construction and connection notes
- Power supply:
- If the supply voltage is higher than 5 V, connect it to the RAW pin, which is connected to the stabilizer.
- VCC is connected directly to the pins of the microcontroller, connecting a voltage higher than 5 V can permanently damage the chip.
- Inputs/Outputs:
- Arduino Pro has 14 digital input/output (I/O) leads.
- Each pin allows a maximum current draw of 40 mA, allowing direct connection of LEDs with resistors and control of other ICs.
- In addition to standard I/O, some leads also have special functions.
- Programming:
- Software development and uploading is enabled by a free environment provided by the manufacturer.
- For programming via UART, you can use the PL2303 programmer.
Important and useful pages and descriptions
- Arduino Pro Mini homepage - http://www.arduino.cc/en/Main/arduinoBoardNano
- IDE program - http://www.arduino.cc/en/Main/Software
- Nano V3.0 board pinout errors - http://microcontrollers.cba.en/?p=6
- USB chip driver - http://www.driverscape.com/download/usb-serial-ch341
Description of the leads
Example application in the project
Included
- NANO V3.0 16MHz USB - ATmega328PB - CH340 - Clone - 1 pc
Write your opinion
Brand
Entity responsible for this product in the EU
JH Global Trading (HK) Co., LimitedMore
ProducerJH Global Trading (HK) Co., LimitedAddress:
Room G, Floor 10, Block A, Duhui Electronic Building, Huaqiang Road 10Postal Code: CN 518031City: ShenzhenCountry: ChinyPhone number: 86 075582557429E-mail: info@jh-electronica.com
Responsible entityABC-RC Firma LedaAddress:
Judy Tadeusza 9Postal Code: 34-122City: NidekCountry: PolskaPhone number: 333-003-080E-mail: pomoc@abc-rc.pl
Symbol
9588
Producer code
5904384710492
Status
New
Manufacturer code
9588
Rodzaj
driver
Manufacturer
unbranded
Ask for this product